Woodworking Process - Cabinet Making

First, the definition of cabinet production

In general, cabinet production includes wooden parts such as wardrobes, bookcases, lockers, and TV cabinets.

Second, the cabinet production precautions

1, the cabinet does not see the light at the close of the use of the corresponding panel shut, the production of the cabinet door with 15mm wood panel strip, the bar spacing does not exceed 15cm, double-sided paste 3MM veneer, the front veneer pick the entire veneer, wood grain Must be smooth and beautiful. The panel must be straight and the seams are dense. The thickness of each door must be the same. The vertical interface of the panel adopts a 45° angle, and the gap between the doors of the coated plastic cabinet should not be misaligned between 1.5-2.5mm.

2. The horizontal and vertical intersections of the cabinet racks must be straight and tightly jointed. The fire board must not collapse, and the over-drum phenomenon must occur. The backboard must be strong enough (five-story boards are attached to the inner board.

3. The dark drawer inside the cabinet must maintain a space distance of 15mm from the cabinet door. The side that depends on the hinge of the pipe must have sufficient space to pull out.

4. The hanging frame of the drying rack in the cabinet is made of stainless steel pipe.

5, cabinet drawers, grid made activities.

6. The dark drawer panel inside the cabinet is consistent with the panel of the cabinet door.

7. The veneer interface regulations on the outside of the wardrobe are left below.

8. The dimensions of the door hinge hinge must be uniform in the same suite.

9. The thickness of the side panels around the drawer must not be less than 12mm.

10. The outer side of the drawer and the back of the floor must be full of inner hall boards.

11. Drawer end plate is tightened with self-tapping screws and the wire head is not allowed to be exposed.

12. The drawer slide rail adopts the three sections of the company's unified distribution. When installing three sections of rails, it is placed on the 1/3 of the façade of the drawer.

13. All suspended laminates, desks, and TV cabinets must be approved by the Engineering Department before they can be constructed.

14, the activities within the collection board around the line. (Applies to fireproof board veneer only

15, wooden products veneer side must close. (except for fire board fights

16. The woodwork frame must meet the force requirements.

17. The auxiliary ribs must be added when the partition, screen or background space exceeds 200mm.

18. The wooden frame of the platform dragon skeleton and the supporting main keel must be placed directly under the frame, and the force point falls at the intersection.

19. Wooden beds must be made into movable beds. Wooden bed board must be embossed panel or wood fire board.

20, the slope of the shoe frame inwards, the back board must leave a dust gap.

21, the door more than 2.1m must install three hinges.

22, the back of the furniture near the fixed glass must be affixed with a white fire board or veneer material.

23. When woodwork seals the ceiling or installs furniture with lights, it must be handed over to the electrician for construction.

24, wine rack production activities. (or according to the owner's request

25, the computer keyboard drawer must try to exceed the desktop 2 / 3 depth.

26. The diagonal dimension error of each space in the frame of the cabinet shall not exceed 2mm.

Third, the cabinet production of several common categories

Wardrobe production

Shoe cabinet production

Locker production

Bookcase production

TV cabinet production

Fourth, the cabinet production process

Cutting: 1, should take full account of the reasonable use of materials, should be opened before the big material, and then open a small material, the final use of spare parts; 2, the length of the cabinet, the height of more than 2400mm, should be divided into two groups The vertical version of the assembly and merging section must be overlapped by two pieces of nine PCT board to ensure that its thickness is basically the same as the thickness of the large core board. 3. If the cabinet adopts alloy sliding doors, the position of the upper and lower rails shall be taken into consideration. The cabinet lining shall be Narrow 90-100mm, plus a layer of veneer; 4, fully consider whether the position of the drawer lock can be normally opened, and then determine the width of the drawer, if the drawer position is at the bottom, the drawer must be raised 20mm Make sure that the drawer can be pulled straight out. If it is a drawer with a flat open door, and the drawer is at the bottom, it should be raised 30mm to ensure that the door can be installed.

Cabinet assembly: 1, before the sheet is attached to the Boeing film, the label on the sheet must be cleaned; 2. The paste of the Boeing film must be smooth, without blistering and damage. 3. When the cabinet is assembled, the mouthpiece of the vertical board must be Positive, horizontal plate on the back of the mouth; 4, before installing the backplane, you must check whether the diagonal line is equal; 5, the back of the cabinet must use PCT board to do the backboard, if the back of the cabinet is tiled, then Must use big core board as backplane

Cabinets are fixed: 1, if it is a partition wall cabinet, the back of the cabinet with a 30 * 40 wooden side, the spacing should not be greater than 300 * 300mm dragon skeleton, then the gypsum board fixed on the dragon skeleton, the dragon skeleton should be added sound insulation Cotton, to ensure the sound insulation effect; 2, all against the wall cabinet stress from the wall 20mm, if it is a new masonry wall should be posted on the back side of a layer of moisture-proof membrane to prevent the cabinet from absorbing moisture and mildew.

Decoration Construction Knowledge Carpentry Knowledge TV Home Furnishing Space Furniture TV Decoration Home Improvement Home Improvement TV Backgrounds Home Decorating Wall Decoration Partition Glass Bricks Drawer Cabinets Cabinets Doors Lockers Glass Cabinets Craft Glass Partition Cabinets Wall Cabinets Glass Doors Glass Sliding Doors Doors Doors Doors Glass Tables Glass Doors Doors Tiles Tiles Tiles Walls Walls Tiles

Stainless Steal CNC Milling Parts

Stainless Steal Cnc Milling Parts,Aluminum Parts Cnc Machining,Metal Cnc Machining,Luninum Cnc Machining

JIANGSU TONGDE INTERNATIONAL TRADE CO.LTD. , https://www.tongdetrade.com