Glass doors can be seen everywhere in daily life. Because of their beautiful appearance and moderate price, they are widely used in offices, shops, hotels and other places. So, do you know how to install the glass door? What are the types of glass doors? The following Xiao Bian gave you talk about glass door installation steps and the types of glass doors. Let's take a look.

What are the glass door installation steps?

1, positioning, put line

Combination of fixed glass and movable glass door leaf glass door, unified positioning of the line, according to the requirements of the design and construction drawings, release the positioning of the glass door, while determining the position of the door frame.

2, the installation box top limit slot

The width of the limiting slot shall be greater than the thickness of the glass by two to four millimeters, and the depth of the slot shall be 10-20mm. When installing, two metal decorative plate edges shall be led from the midline of the bullet, and then the limiting slot shall be installed at the top of the frame according to the edge. , Adjust the groove depth in the slot through the glue pad.

3, the installation of metal veneer wooden tray

The square wood is fixed on the ground, and the metal veneer is glued on the wood with all-purpose adhesive. If the aluminum alloy square tube is used, the aluminum angle can be fixed on the frame pillar, or the wooden bricks embedded in the ground can be fixed with wooden screws. on.

4, install the vertical door frame

The centerline nails the door and frame the square wood, and then the plywood is used to determine the shape and position of the frame pillar, and finally the metal decorative surface is covered. When decorating the bag, place the facing seams on the head in the middle door position on both sides of the installation glass.

5, install the glass

The glass sucker is used to suck the thick glass and lift the thick glass plate to the installation position. First insert the upper part of the glass into the limit slot at the top of the door frame, and then put the lower part of the glass on the bottom support.

6, fixed glass

Two small wooden sticks on the inside and outside of the bottom bracket are used to sandwich the thick glass in the middle door. The square sticks are coated with all-purpose adhesive and the decorative metal is glued to the square wood strips.

7, injection glass seal

In the gaps at the top of the top and bottom brackets, and at the gaps between the thick glass and the frame column, inject the glass seal and use a tool to scrape the excess glass glue.

8, glass docking

When the fixed part of the glass door is required to be spliced ​​due to its large size, the seam must have a width of two to three millimeters, and the edge of the glass plate should be chamfered.

9, floor spring installation

Before the installation of the door leaf, the positioning pins of the ground spring and the top surface of the door frame shall be installed and must be coaxial. It is better to use the vertical line inspection to ensure that they are on the same straight line.

10, install the upper and lower door clip

Put the upper and lower metal door clips on the upper and lower ends of the glass door respectively. If the door leaf is not high enough, you can insert the wood clips on the glass bottom of the lower door clip.

11, fixed glass door clip

After setting the height of the door leaf, insert small wooden strips on both sides of the gap between the glass and the upper and lower door clamps, and inject glass glue into the gap.

12, door installation

First, adjust the positioning pin with its own adjusting screw out of the plane of the beam by two millimeters, erect the office glass door leaf, align the hole of the rotating pin connector in the lower door leaf of the door leaf with the rotation pin of the spring, and turn the door leaf to position the hole. Put on the pin shaft, turn the door leaf at right angles to the beam of the door frame, align the holes in the door clamp on the door leaf with the positioning pin on the beam of the door frame, adjust the adjusting screw of the positioning pin, and insert the positioning pin into the hole.

13, handle installation

Before installation, apply a small amount of glass glue to the part where the handle is inserted into the glass. When the handle is assembled, tighten the root with the glass and tighten the screws to ensure that the handle is not loose.

Glass door type introduction

1, decorative glass door

Decorative glass doors not only serve as the role of the door, there are certain decorative effects, including frosted glass, embossed glass, carved glass, glazed glass and other types, mainly produced different patterns. Its advantages are different colors, good gloss effect, rich decorative effect, and corrosion resistance, easy cleaning, anti-erosion and so on.

2, safety glass door

The most important feature of safety glass doors is safety. Due to the manufacturing process, considering the dangers of glass, safety considerations are applied in production. Including tempered glass, bullet-proof glass, wire glass and laminated glass, good lighting, easy to clean, good thermal stability, not scattered after fragmentation, not easy to hurt.

3, energy-saving glass door

The energy-saving glass door has the function of heat insulation and heat preservation, and it adopts a special process and coloring to the glass so that it can effectively absorb the heat of the solar radiation and achieve the energy-saving effect. Second, it absorbs ultraviolet rays and visible light to prevent ultraviolet rays from affecting the interior and soften the light.

The above is about the glass door installation steps and the types of glass doors, I believe we all understand it! The use of glass doors is very extensive. Therefore, we must learn more about the knowledge of glass doors and hope that the above content can help everyone.

Glass door

Clawfoot Bathtub

Clawfoot Bathtub

Clawfoot Bathtub

Guangzhou Aijingsi Sanitary Products Co.,Ltd , https://www.comoxvalleyhottubs.com