Reasons for the fatigue damage of the bearing and the solution
Posted on

Home>Bearing knowledge>The cause and solution of bearing fatigue damage
/*728*90 created on 2018/5/16*/ var cpro_id = "u3440131";

Reasons for the fatigue damage of the bearing and the solution

Source: China Bearing Network Time: 2014-07-20
/*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089';
Some of the top of the list: the appearance of bearing fatigue damage analysis:
1), the length of the bearing from the beginning of the use of the first information exhausted by the guide is the speed of the bearing; the load is large.
2), fatigue is the result of the periodic presentation of the shear stress under the load surface; after a period of time; these shear stresses cause a slender cranium; then gradually extend to the appearance; when the rolling member passes through these split skulls; The crack falls; it constitutes the so-called "peeling appearance"; then the condition of peeling continues to expand; the bearing is damaged.
3) The above is a depiction of bearing fatigue; it begins to occur below the surface; although the initial stripping condition is generally very slender; however, the addition of stress and the increase of cracks; the extension of the stripping area; Keep it for a long time; its noticeable period is when noise and sensation are added.
4), the bicycle bearing during the initial stage of damage; can only be difficult to feel when changing; and later found that there is a pockmark when changing; but once the pockmark is felt; the bearing is not unusable; just every time Both the beads and the shaft bowl and the shaft file have more wear and more severe damage; because the bicycle is a low-speed high-pressure type bearing method; therefore, even if the appearance of skin peeling is severe; it is not used; it is invisible and silent. It takes your motivation; and your feelings can only be that the car doesn’t know why it’s not good enough.
5), therefore before the bearing is completely damaged; it provides the discovery moment that the operator satisfies; do not ignore the existence of such conflict; it will reduce the speed of riding; let the long-distance force cost more and slower.
If the roughness of the appearance is slender; if the lubricant film has the proper thickness; then the probability of external stress generation is properly low; this is why it is appropriate to properly select the appropriate oil for lubrication; however; if the pressure load exceeds The pu value of the oil film (the fatigue load limit value; such as excessive speed; excessive pressure impact); then the fatigue of the data will come sooner or later.
The second part: the cause of the bearing damage and the solution:
1), one of the reasons for the early damage of the bearing is not properly lubricated, although it can be equipped with "protection-free" rubber-sealed bearings; however, the premature failure of the bearing still has a percentage of 36 because of the incorrect use of grease skills.
Any bearing that is not properly lubricated; failure to avoid early failure; because the bearing is the part of the hub that is not easy to assemble and disassemble; and the innate grease is used innately; and the grease is not replaced in later use; perhaps in the grease It will not be replaced in time after the carbonization and pollution change; then it is difficult for your hub to meet the long life and excellent lubrication.
The bicycles used in bicycles nowadays encounter small standard bearings that are mostly deep groove balls; such as 609; 6000; 6001; 6200; these are industrially used for the stator and rotor of small-scale motors; Such small Peeling is generally pre-installed with low viscosity; high-lubricity broad-spectrum grease.
In the past, we used to buy and use the most expensive greases of this kind; for example, we used the SKF LGMT-2 to form lithium-based grease; this is a low-torque, low-conflict small motor. Lubricating oil; also used in most small skf Palin; the price is still very expensive; the price of 200 grams of packaging is up to 60 yuan; but the viscosity of this oil is only 110; for high load; extreme pressure Reciprocating ability is poor; and according to the use of the bicycle shaft; this should be a low speed; high extreme pressure (because a lot of pressure will only be concentrated on a few fine Palin; and the impact will occur more Great pressure); So we later selected SKF's LGEP-2 to form lithium base grease; this is expensive (155 yuan); however, its viscosity reaches 200; high load; high waterproof; high rust resistance; Although it is not as good as LGMT-2 in the low torque conflict indicator, it is completely suitable for the front and rear axles and the front bowl of the bicycle (today we have some old hubs; if the rm40 correction is LGEP-2 lubrication).
2), the reason for the early damage of the bearing is not properly installed, the other damage is up to 16%; this is not the installation; and the fault is perhaps violent loading; so that the Palin is already in the attack Lubricate the outer surface of the bowl.
In order to make the Palin card tightly axis; avoid the occurrence of the sleeve conflicting image (this kind of appearance will occur when the high-speed transformation of the machine is high; the formation of lubricating oil burns and even causes the heat to rise and jam; form a stop); The bowl and the outer bowl (also known as the bearing box in the industry) use an "overweight" appearance; in a nutshell, the shaft is larger than the inner one; perhaps the outer bowl is larger than the load; this kind of interference requires a lot of strength to dry up Into such; the loading requires a great effort to strike the Palin; this will form the damage of the Palin in the process of tapping; therefore, the industrial large bearings generally use heating; hydraulic jacking and other methods.
Bicycles use glued deep groove ball bearings; such bearings are most afraid of knocking (the needles of Palin and Da Pei Lin are slightly more resistant to percussion); and they are not used for heating; but because of the bicycle Palin's over-profit is very good. 踔寥缜 琅嗔 琅嗔 琅嗔 目 目 目 杂 杂 杂 凰 凰 凰 凰 凰 凰 凰 凰 凰 凰 凰 凰 凰 凰 凰 凰 凰 那 那 那 那 那 那 那 那 那 那 那 那降 砻妫 砻妫 褂 褂 褂 褂 褂 褂 褂 褂 褂 褂 褂 褂 褂 褂 褂 褂 褂 褂 褂
Recommend to friends comments close window

Bearing related knowledge
SKF imported bearing selection method
LYC wind power bearing quenching and tempering heat treatment process; obtaining a serious breakthrough in the selection of 10 elements of cylindrical bearing equipment for the selection of imported bearings, the layout function of five major types of bearings in plastic machinery and its characteristics


This article links to http://
Please indicate the bearing network http://

Previous:Discriminate the standard requirements of bearings, focus on the local next: How to properly install and disassemble NSK bearings

Holster Measuring Tape

Holster Measuring Tape,Steel Tape Measure With Self-Locking,Steel Tape Measure With Magnet,Steel Tape Measure With Abs

Shangqiu Jinda Tools Co.,Ltd , https://www.jindameasur.com