The In-Wall Bidet Frame is a sturdy iron frame specifically designed to provide support for wall-mounted bidets. By fitting into the wall, it effectively conceals the bidet's tank and plumbing, resulting in a modern and streamlined appearance for the bathroom. In Wall Bidet Frame, Wall Hung Bidet Frame, Wall Hung Bidet Holder, In Wall Bidet Holder Guangdong Fabia Intelligent Technology Co., Ltd , https://www.smartfabiatoilet.com
/*728*90 created on 2018/5/16*/ var cpro_id = "u3440131"; Home>Bearing knowledge> Precision after fine SKF bearing unit Precision after fine SKF bearing unit
Thin> å²£å» å²£å» bearing in the host after the end of the device; such as measuring the radial runout of the spindle; can be found that each of the measured values ​​have a certain change, continuous measurement; can be found after passing a certain number of revolutions; This change will be approximately repeated. The target for measuring the degree of this change is the cycle rotation precision; changing the number of revolutions required to approximately repeat the presentation represents the "quasi-period" of the cycle rotation accuracy; the magnitude change in the quasi-period changes the magnitude Large; that is, the rotation rotation accuracy is poor. /*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089';
For example, the preload is properly applied to the main shaft; the rotational speed is gradually increased to the near-operation speed; the "run-in" effect of the bearing is implemented; the cyclic rotation accuracy of the main shaft can be improved.
2. One way to improve the accuracy of the bearing is to produce a fine instrument in a factory; the main shaft is used with the 6202/P2 type bearing and its accuracy is still not satisfactory; the rear journal is thickened and a raceway is made on it to replace the inner ring; Measured in detail; each set of three scales; each set of steel balls is separated by a distance of nearly 120°; because it reduces the appearance of a heavy machining; it also reduces the appearance of a cooperation; together, the rigidity of the shaft-bearing system is improved; The maximum three and the smallest three steel balls are nearly equidistantly distributed; the axis reversal accuracy is improved; therefore, the accuracy requirements of the instrument are satisfied.
3. The inductive verification method of the device accuracy is to install the angular touch ball bearing into the main shaft; the verification order of the device accuracy is as follows (for example, a general lathe with a shaft diameter of 60 100 mm):
(1) Measuring the dimensions of the shaft and the bearing housing hole; to determine the cooperation precision of the bearing; the cooperation requirements are as follows:
The inner ring and the shaft adopt the interference cooperation; the interference is 0～+4μm (0 in light load and high precision), the outer ring and the bearing housing hole adopt the gap cooperation; the clearance is 0～+6μm (but the bearing at the free end) When the angular contact ball bearing is used; the gap can be increased), the circularity of the shaft and the seat hole is less than 2μm; the parallelism of the end face of the bearing is less than 2μm; the inner end of the shoulder is less than 2μm. The bearing block hole shoulder jumps to the axis below 4μm, and the inner end face of the spindle front cover jumps below 4μm.
(2) The fixed-end bearing on the shaft will completely remove the bearing with clean cleaning oil; the grease is smooth; the organic solvent rich in 3%-5% smooth grease is first written into the bearing for degreasing; Then use the oil gun to fill the bearing with the smooth grease (10% to 15% of the bearing space volume), heat the bearing to raise the temperature by 20 ~ 30 °C; use the hydraulic press to install the bearing into the shaft end, press the adapter sleeve The shaft is placed on the shaft with a suitable pressure to axially position the bearing, and the belt of the spring balance is wound on the outer ring of the bearing; whether the regular preload can be greatly changed by measuring the starting torque (even The bearing is correct; but because of the cooperation or deformation of the cage; the preload can also be changed).
(3) The bearing shaft assembly body is installed in the seat hole heating seat hole to raise the temperature by 20 to 30 ° C, and the bearing shaft assembly body is installed into the seat hole by the successively gentle pressure, and the front cover is adjusted; the fastening amount of the front cover is 0. 02～0. 05μm; based on the outer end of the bearing seat; the head of the dial gauge conflicts on the outer surface of the journal; the shaft is rotated to measure its runout; the demand error is below 10μm, and the dial gauge is positioned on the shaft The head is in conflict with the inside and outside of the seat hole; the shaft is rotated to measure the coaxiality of the front and rear seat holes of the bearing housing.
(4) Selecting the free end bearing in an orientation capable of canceling the error; supporting the bearing after the device is placed to the bearing housing; and canceling the roundness error and the coaxiality error between each other as much as possible.
4. The device with tapered bore double row short cylindrical roller bearing is equipped with NN3000K series tapered bore double row short cylindrical roller bearing; it is necessary to pay attention to the correct matching of the inner diameter of the bearing and the taper of the shaft; the coloring method can be used in the case of less production value. Perform touch verification; but when the production volume is large; it is best to use a fine cone gauge to verify.
When the bearing is mounted on the tapered shaft; the inner ring should be adjusted to the proper orientation in the axial direction; the radial clearance is close to zero.
Recommend to friends comments close window Bearing related knowledge The first process of thrust ball bearing installation is a detailed discussion on the method of distinguishing plastic bearing genuine bearing
FAG bearing error brief measurement bearing professor describes how to look at the problems of cylindrical roller bearings
This article links to http://
Please indicate China Bearing Network http://
Previous:Two ways to measure the preload of the bearing bush compared to the next one: Skill analysis: reducer equipment, operation and protection
Beyond its aesthetic advantages, the in-wall bidet frame offers several functional benefits. One of its primary advantages is the enhanced support it provides for the bidet fixture. This is particularly beneficial for larger individuals or those with limited mobility, as the frame ensures a stable and secure installation. The added support contributes to a comfortable and safe user experience.
The in-wall bidet frame is also height adjustable, allowing for customization to accommodate individual preferences and needs. This feature ensures that users can set the bidet at a comfortable height, promoting optimal usability and convenience.
Moreover, the space-saving design of the in-wall bidet frame is highly advantageous, especially in smaller bathrooms where floor space is limited. By fitting into the wall, the frame eliminates the need for additional floor space, effectively maximizing the available area. This can be particularly valuable for compact bathrooms, as it allows for a more efficient utilization of the available space.
In addition to space-saving benefits, the design of the in-wall bidet frame also facilitates easier cleaning and maintenance. With fewer exposed areas and nooks, there are fewer spaces for dust and grime to accumulate. This simplifies the cleaning process and helps maintain a hygienic environment.
Precision after fine SKF bearing unit
Source: Bearing network time: 2018-06-03