Wall decoration is now a very popular decoration feature, many people will choose the wallpaper when the wall decoration, and now there are many types of wallpaper on the market, one of which is embroidered wallpaper, due to the good anti-mold and embroidered wallpaper is good The air permeability and other issues have been loved by many people. Today, we would like to learn about the construction process and related knowledge of embroidery wallpapers .

Embroidery wallpaper construction process

1. Before the construction, it is necessary to ensure the smoothness and dryness of the wall surface. The construction shall be carried out without falling off. The wall surface shall be treated with moisture-proof treatment. A layer of varnish or white enamel base film may be applied on the wall surface, but the construction shall be dry.

2. The embroidered wallpaper cuts need to add 10cm in accordance with the length, because it takes into consideration that the wallpaper pattern is always on, so the length needs to be increased according to the actual situation.

3. Before sticking, it is necessary to apply a layer of wet glue on the wall surface. Paste the wallpaper in accordance with the order. It is recommended not to glue on the back of the embroidery wallpaper to prevent the glue from penetrating into the color line to cause discoloration.

4. In wallpapering, it is necessary to use soft fur to brush from the top to the bottom, and gently brush it on both sides to make the glue and air bubbles in the wallpaper scrape out. Keep the wallpaper flat against the wall.

5. When wallpapering, because it is a non-woven wallpaper, the watermark will appear on the wall. This is a normal phenomenon, and it will disappear after it has dried naturally.

Embroidery wallpaper maintenance

Blistering

Blistering is one of the most common problems in wallpapers, because the glue is not uniform when the wallpaper is pasted. Therefore, when the surface tension of the later wallpaper is separated from the base layer and the water is too much, the built-in bubbles appear. At this time, only need to take a needle to pierce the position, put the gas inside out, and use a needle to take a small amount of glue to re-bond the wallpaper and the wall, flatten and dry it.

2. Musty

In the case of relatively moist, it will easily lead to moldy wallpaper wall. If mildew is not serious, wipe it with a white towel, or wipe it with soapy water. It's best to buy a special fungicide at the wallpaper shop.

3. Alice

When the grass is not processed cleanly or the glue is not sticky enough, there will be a problem of edging. At this time, you can use the wallpaper glue, wipe it at the curling edge, smooth out the curls, and blow it with a hair dryer for about 10 seconds. Press it firmly by hand until it sticks. Blow it with a hair dryer and dry it.

4. Scrub

If the wallpaper has spots where it appears, wipe the dirty area with a damp cloth. This method can not be used on a wallpaper with color, otherwise it is easy to fade. Wipe the wallpaper should begin in some avoidable corners or hidden behind the door to avoid adverse reactions caused by wallpaper damage.

The above is the introduction of embroidery wallpaper for everyone. After reading it, is there more understanding of this aspect? If you just want to choose a friend who can decorate the wall, you can check it out! It must be able to help you. Oh, if you want to know more information, please continue to pay attention to this site, more exciting so stay tuned!

Wallpaper wallpaper maintenance

Taper Shank Drill Bit

The Morse taper shank Drill Bit is a self-locking (or self holding) taper of approximately 5/8" per foot that allows the torque to be transferred to the drill bit by the friction between the taper shank and the socket. The tang at the end of the taper is only for ejecting the drill bit from the spindle, with the aid of a drift.

The arbor of a drill chuck is often a Morse taper and this allows the chuck assembly to be removed and directly replaced with the shank of a Morse taper drill bit.

Its material is high speed steel,treatment process is roll-forged

Taper Shank Drill Bit,Shank Drill Bit,Taper Shank Drills,Twist Drill

Behappy Crafts (suzhou)Co.,Ltd , https://www.craftsbehappy.com