TV wardrobe brand wine cabinet decorative cabinet door cabinet drawer cabinet cupboard door Elevator Switch Or Sensor,Host To Host,Host Brake Switch,Elevator Microswitch Suzhou FUJI Precision Elevator Co.,Ltd , https://www.profuji.com
02. Check the purchased materials and use them only after they are qualified. Carpentry for the use of ingredients: A. decorative panel color difference is small, no flaws on the board, damage. B. Pick and choose strips are used with uniform color and no obvious defects.
03. Cutting and cutting, combing the base cabinet to check the combination accuracy; verticality ≤ 2mm, horizontal error ≤ 1mm, warpage ≤ 2mm.
04. The horizontal wood panel in the cabinet at the partition between the upper and lower cabinet doors of the cabinet should be reinforced with double layers to strengthen the strength and avoid cabinet deformation. The maximum length of the door should generally be ≤1650mm.
05. Cabinet back plate should be fixed firmly.
06. When plywood panels are applied in cabinets, they shall be cleaned, polished and then affixed with white latex, and then fixed with a few mosquito fasteners. The joints should be uniform and tidy, and all wooden cabinets should be fixed. The connection must be fixed with white latex and then nailed.
07. Door leaf production: 1 Select the use of wood board strips, and carry out cross-openings; 2 Facing the front panel to select the entire panel veneer, the wood grain is straight and beautiful, and the back is covered with the corresponding decorative panel;
3 Qingguang door leaf, check the geometric dimensions, diagonal and peripheral error ≤ 1mm; 4 unified number placed.
08. After the production of the door leaf is completed, it shall be placed on a flat site and pressed with heavy objects, or topped with wood. No less than 3 days. After picking the mouth line, it is pushed and used, and the seams are straight and clean. There are joints at the corners and at the corners and horizontal and vertical grids. No joints are allowed at other places. No obvious seam is found at a distance of 1 meter. Trim the edges carefully to prevent damage to the panel.
09. The door leaf is decorated with flowers and the construction according to the figure shall be accurate in size, and the joints shall be even and beautiful, and shall be smooth and free from unevenness.
10. The door leaf is properly installed in the order of production. The wood grain is straight, beautiful, and the geometric dimensions are correct. The gap size between the doors is 2-3mm. Cabinets should be designed under normal circumstances, cabinet caps should be beyond the closed door 3-5mm.
11. The door length exceeds 1600mm must install 3 hinges. The hinges need to be fastened, flexible to open, complete screws, easy slides, clean cabinets and open doors.
12.1 Hanger height 1.8 meters; 2 long coat 1250, short coat 1020, suit 780, dress 1100; 3 bookcases, small books are generally 210 high x 150 wide (16 open), medium book 300 high x 220 wide; 4 wardrobe depth 550-600, wardrobe internal drawer height 200, bookcase depth 280-350; 5 computer desk height 700-750 pull pumping 100-120 high; 6 computer box 450 high x 200 width x 450 deep, keyboard slide is not Less than empty 500; 7 wine cabinets divided high 300-450; 8 balcony low cabinet 800-900 thick 400-600; 929-34 inch TV cabinet used TV is about 450, rear projection TV cabinet height 150-200; 10VCD width 428 × 360 × 90 power amplifier 428 × 360 × 120 medium audio 300 × 350 × 900, all cabinet kick angle of 80.
Construction process site construction method 3--furniture engineering
01. Familiar with the design, construction according to the plan. The construction workers shall be given technical disclosure, the amount of material shall be calculated, the construction plan shall be determined, the customer's opinions shall be solicited by the division within the cabinet, and the partition shall be carried out by means of a combination of fixed partitions and movable partitions.